Tuning Wiki
Browse Alpine Renault

The car

The 2018 Alpine A110 uses a 1.8 litre turbocharged four-cylinder that PistonHeads describes as essentially the Renault Sport Megane Trophy engine with a lower-inertia turbo and different software. A UK remap shop lists the controller on a 248 bhp 2018 car as a Hitachi BED501. Alpine's earlier cars are covered on Alpine: history and cars; the later Megane family is on Megane IV RS 280 and 300.

Quoted gains

RouteClaimSource type
Piggyback module, stage 2Up 53 hp to 305 hp and up 59 lb ft to a 298 lb ft peak, from a 1,080 kg car; £499, with a two-year engine warrantyMaker claim reported by PistonHeads (2019)
Piggyback module, stage 1An additional +43 hp and +49 lb ft for £349 (no baseline given)Same article
ECU remap on the 252 hp carAbout +33 hp and +85 to +110 Nm; one listing shows 285 hp and 430 NmTuner listings
Remap, one tuner300 hp and 298 lb ft, +52 hp and +62 lb ftTuner claim
Stage 1, reseller estimateRoughly 10% on the 252 hp carReseller
A110 S, custom ECU calibration with a raised rev limiter280 hp and 376 Nm to 303 hp and 424 Nm (+23 hp, +48 Nm)K-Tec Racing, 2WD Dimsport dyno

Prices run from about €399 to €690 in Europe and £990 to £995 before VAT in the UK. All power figures are maker or vendor claims. RaceChip's autobahn comparison (1.5 seconds quicker from 100 to 200 km/h on a hot day) is the only performance test cited and is the maker's own.

The gearbox is the real constraint

The seven-speed wet-clutch dual-clutch gearbox is repeatedly named as the limiting component. Reports state that Alpine rates it for no more than about 236 lb ft (and that later cars stayed near 250 lb ft because of it), and a French report says some believe it struggles with much more than the standard 320 Nm. A UK tuner says its map raises the maximum torque limiters, speeds gear changes and increases clutch clamping pressure to avoid wear. The primary press sources for these torque limits were not accessible, so the figures are reported rather than confirmed. In practical terms, any map that lifts torque well above standard should also address the gearbox, not just the engine.

ECU plus gearbox tuning on the A110 S

K-Tec Racing describes a near-new A110 S (GPF model) with a calibration written for the individual car, a raised rev limiter and an optional gearbox control-unit tune that adjusts clamping pressures and shift points for quicker, crisper changes. The company measured 303 hp and 424 Nm against a stock 280 hp and 376 Nm on a two-wheel-drive Dimsport dyno, logging boost, fuel and intake temperatures. No correction factor, ambient conditions or fuel are stated, the graph is an image and the shift and clamping values are not given. K-Tec says the result beats two competing tunes (295 hp and 380 Nm; 305 hp and 415 Nm), but its own 303 hp is below the second figure, so the claim holds only for torque. Treat the page as an example of a combined ECU and gearbox approach, not as validated data.

Other points

  • A larger air-to-water intercooler appears in one owner's staged build; no data on whether the standard cooler limits a stage 1 car was found.
  • A piggyback module leaves the original ECU untouched, which keeps the factory calibration recoverable but also leaves the factory torque limiters in place.

Not documented

Safe torque limits for the clutch pack, intercooler headroom, boost targets and independent dyno measurements.

Sources